Alcatel OmniAccess 2.0 Manual de usuario descargar pdf (Pagina 2)

2

Alcatel-Lucent OmniAccess RAP3

ALCATELLUCENT ENTERPRISE DATA SHEET

Wireless Radio Speciﬁcations

• AP type: 2.4 GHz 802.11n indoor

• Software-conﬁgurable 2.4-GHz radio

• 2×2 MIMO 802.11n with two spatial

streams and up to300 Mbps wireless

data rate

• Supported frequency band (country-

speciﬁc restrictions apply): 2.4000 GHz

to 2.4835 GHz

• Available channels: Managed by Virtual

Controller or Mobility Controller,

dependent upon conﬁgured

regulatory domain

• Supported radio technologies:

¬ 802.11b: Direct-sequence spread-

spectrum (DSSS)

¬ 802.11n: Orthogonal frequency division

multiplexing (OFDM)

¬ 802.11n: 2x2 MIMO with 2 spatial

streams

• Supported modulation types:

¬ 802.11b: BPSK, QPSK, CCK

¬ 802.11n: BPSK, QPSK, 16-QAM, 64-QAM

• Transmit power: Conﬁgurable in

increments of 0.5 dBm

• Maximum (aggregate) transmit power:

+19 dBm (limited by local regulatory

requirements)

• Maximum ratio combining (MRC) for

improved receiver performance

• Cyclic Delay Diversity for improved

downlink RF performance

• Short guard interval for 20-MHz and

40-MHz channels

• Space time blocking code (STBC) for

increased range and improved reception

• Association rates (Mbps):

¬ 802.11b: 1, 2, 5.5, 11

¬ 802.11: 6, 9, 12, 18, 24, 36, 48, 54

¬ 802.11n: MCS0 - MCS15 (6.5 Mbps -

300 Mbps)

• 802.11n high-throughput (HT) Support:

HT 20/40

• 802.11n packet aggregation: A-MPDU,

A-MSDU

Power In

• AC-to-DC power adapter (included)

– RAP3WN:

¬ AC input: 100-240 volts AC/0.5 A

¬ DC output: 12 volts DC/1.5 A

• AC-to-DC power adapter (included)

– RAP3WNP:

¬ AC input: 100-240 volts AC/0.75 A

¬ DC output: 48 volts DC/0.75 A

• Maximum power consumption – RAP3WN:

¬ Maximum (excluding USB): 4.0 watts

¬ Maximum (using USB): 6.5 watts

• Maximum power consumption

– RAP3WNP:

¬ Maximum (excluding USB and PoE):

5.5 watts

¬ Maximum (using USB, no PoE): 8.0 watts

¬ Maximum (using USB, full PoE): 26 watts

Antenna

• Two integrated, omni-directional antenna

elements for 2×2 MIMO

• Antenna gain: 2.0 dBi

Interfaces

• Network:

¬ E0 (WAN): One 10/100BASE-T Ethernet

(RJ-45), auto-sensing link speed and

MDI/MDX

¬ E1-E2 (LAN): Two 10/100BASE-T

Ethernet (RJ-45), auto-sensing

link speed and MDI/MDX

¬ Optional 802.3af PoE (15.4 watts) on

the E2 port for IP phones and other

equipment

• Power:

¬ 1 x DC power connector

• Other:

¬ One USB 2.0 port (Type A connector)

¬ One four-pin console interface (custom)

Mounting

• Desktop (using stand supplied with

product)

• Wall (using optional wall-mount accessory)

Mechanical

• Dimensions/weight (unit with desk stand):

¬ 129 mm x 109 mm x 64 mm

(5.1” x 4.3” x 2.5”)

¬ 180 g (6.6 oz)

• Dimensions/weight (shipping):

¬ 218 mm x 150 mm x 64 mm

(8.6” x 5.9” x 2.5”)

¬ RAP3WN: 510 g (1.1 lb)

¬ RAP3WNP: 620 g (1.4 lb)

Environmental

• Operating:

¬ Temperature: 0° C to 40° C

(+32° F to +104° F)

¬ Humidity: 5 to 95% non-condensing

• Storage and transportation temperature

range:

¬ Temperature: -40°C to +70° C

(-40° F to +15 8°F)

Regulatory

• FCC/Industry of Canada

• CE Marked

• R&TTE Directive 1995/5/EC

• Low Voltage Directive 72/23/EEC

• EN 300 328

• EN 301 489

• UL/IEC/EN 60950

Certiﬁcations

• CB Scheme Safety, cTUVus

• Wi-Fi certiﬁed 802.11a/b/g/n

Warranty

• Limited lifetime warranty

Minimum AOS version

• 6.1.4.0

• Instant 3.0

Table 1. RF performance table

1 2 3 4

Comentarios a estos manuales

Sin comentarios